Battle For the Bucket

Tuesday, August 12th 2025 @the  7:00pm

Registration begins @ 6:00pm with walk thru @ 6:30pm

Location at the Firemans Tower

Individual competition and Team competition

Antique Tractor, Car & Machinery

Wednesday, August 13th 2025 – 7:00pm

Machinery Prize:

1st – $25.00

2nd – $15.00

3rd – $10.00

Tractor Pull

Wednesday, August 13th and Thursday, August 14th

FWD, Gas – Prize Money: $300
1st-$100, 2nd-$80, 3rd-$60, 4th-$40, 5th-$20

FWD, Street Diesel – Prize Money: $300
1st-$100, 2nd-$80, 3rd-$60, 4th-$40, 5th-$20

FWD, Open – Prize Money: $500
1st-$200, 2nd-$125, 3rd-$100, 4th-$75

Demolition Derby

Saturday, August 16th @ 5:00pm
Power Wheels and Front Wheel Drive
Power w/ Wheels Powder Puff
Survivor Derby

***Inspections start at 1:00 PM and end at 4:30pm. If you aren’t flagged by 4:30 pm, you won’t get to run. Power wheels starts at 5:00pm and derby starts directly after at 6:00pm***

$50 Entry Fee

4/6 Payouts: 1st – $1500 , 2nd – $500 , 3rd – $300
Powder Puff $500
Survivor $500
that gets one more in the pits with you any one else is $15.00 per person and must be 18 years of age.

Rules:

1. Front wheel drive and powder puff must be a front wheel drive car only 4 or 6 cylinder.
2. You can swap the bumper to any car bumper and it can be welded no added metal or bumper shock.
3. The only weld on the car is the front bumper and a 2×4 plate on the driver door one on the fender side and one on the handle side that is all. 
4. No other welding at all on the car.
5. The car must be stock, if anything is not, you will load your car.
6. DOT tires only. No doubling of tires.
7. You can tuck the trunk and notch the frame. NO creasing at all.
8. All glass must be removed from the vehicle. removing front windshield is optional.
9. Airbags must be removed, not just disconnected.
10. Doors must be wired or chained.
11. No reinforcing subframe, no added bolts.
12. Battery can remain in stock location, or moved to passenger side floor board and securely fastened.
13. Must have helmet, eye protection, and working seat belt.
14. No carb swaps, this is meant to be a stock class.
15. Car must bounce, will be checked after derby.
16. THIS IS A STOCK DERBY.

4 & 6 Cyl Small Cars

***Inspections start at 1:00 PM and end at 4:30pm. If you aren’t flagged by 4:30 pm, you won’t get to run! Power wheels starts at 5:00pm and derby starts directly after at 6:00pm***

**Fresh Cars Only**

Saturday, August 16, 2025 @ 6:00pm
FAT BOY PROMOTIONS

Wheel & Tires:

1. Any Wheel Tire

Frames

2. Absolutely no plates on frame or subframe

Suspension

3. All suspension must bounce freely
4. Can have fixed tie rods

Bumpers

5. Any 80s and up stock bumper
6. May run 4×4 square tubing 1/4″ thick, you are not allowed to weld a point on the tubing. Just a flat piece of 4×4 tubing. Need to be able to see through the ends of the bumper.
7. You can hardnose the bumper but has to have at least 1 inch from the back of the bumper to the core support. Do not move the core support.
8. You are allowed a mounting plate of 1/4 inch thick, 1 inch bigger than your factory frame rail.
9. Rear bumper must stay factory to car.
10. No bumper shocks at all.

Body

11. You are allowed 2 plates per seam below the window. Absolutely no plates and no bolts above window. Use duct tape only. Which means (6) 2×3 plates on a 4-door car or (4) 2×3 plates on a 2-door car.
12. Hood can be held down in 4 places: Either by nine wire or 2×2 3-inch long angle with 1-1/2″ bolt through angle.
13. Factory engine mountains on bottom.
14. Top engine mounts can be changed to square tubing but must still bolt up.

Cage

15. 2×6 5-foot-long doors bars
16. 3×3 front and rear bars
17. Roll over bar must be vertical and no slanted
18. No down bars at all
19. Gas tank protector no wider than 28 inches
20. Gas tank protector can not go back any farther than where the back seat mounted and can not go any higher than the speaker deck.

Trunk

21. You can V the truck
22. You can U the truck
23. You can tuck the truck
24. You can crease the quarters but must stay standing
25. You can use a total of (6) 2×3 plates to weld down your trunk lid.
26. No rear window bar
– Carb swaps are allowed
– No reinforced shifter brackets

***IF IT DOES NOT SAY IT IN THE RULES, JUST DON’T DO IT. DO NOT BUILD IN THE GRAY AREAS OR YOU WILL BE LOADED***

***Inspections start at 1:00 PM and end at 4:30pm. If you aren’t flagged by 4:30 pm, you won’t get to run. Power wheels starts at 5:00pm and derby starts directly after at 6:00pm***

Payouts:
1st place – $3000
2nd place – $1500
3rd place – $700
Mad Dog – $800

V8 big car rules

Saturday, August 16, 2025 @ 7:00pm

Wheels & Tires

1. Any wheel and tire

Rearends

2. Any 5 lug rearend
3. Can be braced but cannot strengthen car in any way
4. Rearend must bounce

Frames

5. No pilates
6. No tilting, no cold bending
7. No welding on frames PERIOD! Pre-runs are allowed (1) 4×4 plate per side. “User Wisely”
8. You are allowed to dimple rear frame for rear bumper to roll. THAT IS IT!

Suspension

9. You can weld (1) 3×3 plate to hold a-arm down *ABSOLUTELY NO OTHER PLATES ALLOWED EXCEPT ON PRE-RUNS
10. 98-02 can swap upper control arms to old style but cannot have the center bar.
11. You are allowed fixed tie rods

Bumpers

12. Any Bumpers allowed
13. No more than 8-inch point at 36 inch spread on pointy bumpers
14. You can hard nose
15. You can only cut back to the core support mounting bracket Do not cut into the bracket.
16. If you hard nose, no bumper shock allowed at all.
17. Rear bumpers must stay stay factory.
18. Bumpers can be no lower than 16 inches and no higher than 24 inches measured from the bottom.

Body

19. Have to use factory body bolts and factory body bushings
20. You are allowed 2 plates per seam below window. Absolutely NO plates and NO bolts above window. Use duct tape only. Which means (6) 2×3 plates on a 4-door car or (4) 2×3 plates on a 2-door car.
21. You can run 1-inch all thread for core support and hood mount with no more than a 3-inch spacer max. That 3 inch spacer goes on top of the core support mounting bracket not on the side of the frame.
22. You are allowed a total of 6 hood mounting spots. Two of those are your all thread, the other four can be nine wire or 2×2 3″ long angle with 1 1/2 bolt through angle.

Trunk

23. You can V the truck
24. You can U the truck
25. You can tuck the truck
26. You can crease the rear quarters but they must remain standing
27. You can use (6) 2×3 plates to weld trunk lid to rear quarters and to the speaker deck. No more than 6 plates allowed.
28. No window bars.

Cage

29. Front bar has to be 6 inches away from tunnel and 6 inches away from firewall.
30. 2×6 door bars, 3×3 front and rear bars. Door bars are to be no longer than 6 foot. No down bars at all. Roll over bars has to stand straight, no slanted.
31. Gas tank protector no bigger than 28 inches wide. Can touch the sheet metal of package tray. Do not weld or bolt to package tray.

03s & Up

– Can follow all of the same rules but steering and suspension on the front of the car have to stay factory.
– Can have bolt in cradle to mount engine with, but it can not strengthen the steering or front suspension in any way. Has to be bolted in, can not be welded in any shape or form.

98 & Up

Allowed the watts link conversion
– Gas pedal has to be bolted through the floorboard sheet metal only. Do not attach to cage in any way.
– Battery box has to be bolted through the floorboard sheet metal only. Do not attach to cage in any way.
– You are allowed the lower cradle and pully protector on engine. No mid-plates
– You can run the ultra bell aluminium on trans but has to be factory tail and no trans brace.

**IF IT IS NOT IN THE RULES, JUST DON’T DO IT. IF YOU BUILD IN THE GREY AREA YOU WILL BE LOADED**

Inspection starts at 4:00pm

1st place – $3000
2nd place – $1500
3rd place – $700
Mad Dog – $800